High Frequency 6 Channels DMX Decoder With DIP Switch

High Frequency 6 Channels DMX Decoder With DIP Switch
High Frequency 6 Channels DMX Decoder With DIP Switch
High Frequency 6 Channels DMX Decoder With DIP Switch
High Frequency 6 Channels DMX Decoder With DIP Switch
High Frequency 6 Channels DMX Decoder With DIP Switch

High Frequency 6 Channels DMX Decoder With DIP Switch

High Frequency DMX Decoder
● Working Voltage DC12-24V & DC25-48V available;
● 6 Channels×5A（DC12-24V),6 Channels×5A(DC25-48V);
● 8Bit(256) & 16Bit(65536) selectable;
● 5K/22K Hz can be choosed.

Send Inquiry

Download

Description

Technical Parameters

product-1-1

Mian Features for 6 channels high frequency DMX decoder with dip switch

Comply with the DMX512/1990 standard protocols;
With RJ45 and XLR interface for DMX IN/OUT selectable;
Converts standard DMX signal to hi-frequency PWM signal;
Refer to LED lights from 12V-48V;
16bit (65536 levels) /8bit (256 levels) grey level selectable;
PWM frequency 5K/22KHz selectable;
Can achieve asynchronous color changes effect under working with controller;
Setting the DMX address freely with Dip Switch.
The 7 output terminals provide 6 independently controllable channels of constant-voltage PWM dimming, and a common anode power
terminal (shared positive).

Mechanical Structures

For the high frequency 6 channels dmx decoder with DIP Switch GDE0605HF, the controller come with DIP Switch in the middle, you can setting the DMX address freely with the DIP Switch. The 6 channels dmx decoder comes with different connection ways:

3pin XLR male connector for DMX in and 3pin XLR female connector for DMX out

RJ45 for DMX in and DMX Out

Green Block Terminals For Power In+, Power In- & LED Output

Mechanical dimensions & Installation

Size in MM: 122*107*33mm

Size in inch:4.8*107*1.3inch

Installation: Installed with mounting holes on both sides, mounting hole pitch 97mm(3.82in.)

Connection and Wiring Diagram

There is a 7 pin phoenix connector socket with two power input pins for a 12/24V power supply, as well as one power output pin and four channel output pins.

A recommended 10 decoders maximum can be chained together on one DMX512 network. To add more unit loads, and for networks longer than 300 meters, a DMX repeater, amplifier, or opto-isolator is needed.

DMX control is only active while the DMX channel is displayed. If the dimming console stops transmitting DMX data, the decoder will retain the last values it received until the device is powered off.

Operation instructions

DMX Signal IN/OUT interface: RJ45 /XLR connector.

DMX address encode with Dip- Switch(N0.1 to N0.9),comply to universal DMX512 dial code.

Dip-Switch NO.10 is TERM for whole signal circle.

Dip-Switch NO.11 for Frequency option ON: 22KHz(H) OFF: 5KHz(L)Dip-Switch NO.12 for Bit option: ON: 16bit OFF: 8bit

NO.11 and NO. 12 change, come into operation when Re-Power on.

SELF-TESTING: put all Dip-Switch NO.1 to NO.9 OFF, full channels output 3 seconds, then each color gradient.

POWER IN DC12-24V, common anode constant voltage output, can meet all kinds of full color module and monochrome module and automatically according to the lamps module load adjust output current, each channel maximum current not more than 10 amps.

Safety Information

1.Install in accordance with national and local electrical code regulations.

2. This product is intended to be installed and serviced by a qualified, licensed electrician.

3. The working voltage for the decoder is DC12-48V, DO NOT connect to high voltage power. Install with a compatible constant voltage power supply or battery with appropriate voltage.

4. Only install compatible 12VDC-48VDC constant voltage luminaires. Make sure to match power supply voltage to the requirements of the LED light. Ignoring this could lead to a potential fire hazard.2

5.This product is rated for indoor use only and is not protected against moisture.

6.Choose an appropriate wire gauge for the maximum potential current load, given your choice of power supply and lights. Keep in mind that the sum total current for all channels is carried over the shared LED+ terminal, so the total current over the LED+ conductor is typically the determining factor in cable choice.

7. Ensure that power is disconnected whenever inserting or removing wires in screw terminals, or connectors in sockets. 8 Ensure that all screw terminals are tightened and all connectors are fully inserted while in operation.

Hot Tags: high frequency 6 channels dmx decoder with dip switch, China, manufacturers, suppliers, factory, customized

Technical Parameters

Products name

High Frequency 6 Channel DMX Decoder with DIP Switch

Products model

GDE0605HF

Housing material & Color

For our 6 channels High frequency DMX Decoder with DIP switch use steel for the housing, and with black color.

Operating voltage

Our 6 channels High frequency DMX Decoder with DIP switch we offer DC12-24V and DC25-48V version.

Output Current(Max.)

Our 6 channels High frequency DMX Decoder with DIP switch for DC12-24V with 6CH×5A, and DC25-48V with 6CH×5A.

Output power(Max.)

Our 6 channels High frequency DMX Decoder with DIP switch for DC12V with 360W max, and DC24V with 720W max, DC48V with 1440W max.

Output type

For our 6 channels High frequency DMX Decoder with DIP switch we offer with constant voltage DC12-48V.

Grey Levels

For our 6 channels High frequency DMX Decoder with DIP switch we offer two different Grey levels selectable 16bit (65536 levels) and 8bit (256 levels).

PWM Frequency

We offer different PWM frequency for you to achieve different requriment, we offer 5K/22KHz Selectable

Gross weight

Gross weight for the High frequency DMX Decoder with DIP switch:400g

Operation temperature

For our DMX decoder, the operation temperature is from -30 ℃ ~ +55℃.

IP rating

The IP Rating for our DMX dercoder is IP40.

DMX IN/ OUT

We offer both RJ45 interface and 3PIN/5PIN XLR for DMX IN/OUT.

Power in/LED Out

We use 10 Pin Green Block Terminals for power in and LED out.