8613510557545victor@glu-light.com
enLanguage

Home / Products / Decoder & Controller & Power Supply / DMX Controller And DMX Decoder / Content
High Frequency 6 Channels DMX Decoder With On-board Display
video

High Frequency 6 Channels DMX Decoder With On-board Display

High Frequency DMX Decoder
● Working Voltage DC12-24V & DC25-48V available;
● 6 Channels×10A（DC12-24V),6 Channels×6A(DC25-48V);
● 8Bit(256) & 16Bit(65536) selectable;
● 5K/10K/20K/30K Hz can be choosed.
Send Inquiry
Download

Description

Technical Parameters

 

product-1600-121

9

 

Mian Features

◆ Comply with the DMX512/1990 standard protocols;

◆ Direct manual control using the LCD screen and buttons;

◆ Converts standard DMX signal to hi-frequency PWM signal;

◆ Refer to LED lights from 12V-48V;

◆16bit (65536 levels) /8bit (256 levels) grey level selectable;

◆ PWM frequency 5K/10K/20K/30KHz selectable;

◆The 7 output terminals provide 6 independently controllable channels of constant-voltage PWM dimming, and a common anode power terminal (shared positive).

 

Mechanical Structures

 

For the high frequency 6 channels dmx decoder with on-board display GDE0610HF, the controller come with a LCD display in the middle, and 3 adjust keys for manual operation. The 6 channels dmx decoder comes with different connection ways:

 
01
 

5pin XLR male connector for DMX in and 5pin XLR female connector for DMX out

 
02
 

 

RJ45 for DMX in and DMX Out

 
03
 

 

Green Block Terminals For Power In+, Power In- & LED Output

17
12

 

Mechanical dimensions & Installation

High frequency 6 channels dmx decoder with on-board display dimeision:

122*107*33mm

4.8*107*1.3inch


High frequency 6 channels dmx decoder with on-board display Installation:

Installed with mounting holes on both sides.

mounting hole pitch 97mm(3.82in.)

 

Connection and Wiring Diagram

Note:
1. There is a 7 pin phoenix connector socket with two power input pins for a 12/24V power supply, as well as one power output pin and four channel output pins.
2. A recommended 10 decoders maximum can be chained together on one DMX512 network. To add more unit loads, and for networks longer than 300 meters, a DMX repeater,
amplifier, or opto-isolator is needed.
3. DMX control is only active while the DMX channel is displayed. If the dimming console stops transmitting DMX data, the decoder will retain the last values it received until the device is powered off.

13
Operation instructions

 

 
14

Key 1

Call up the DMX512 external control and internal dimming program menu, like address code, 8/16bit, PWM frequency, and set manual brightness levels of each channel.

15

Key 2

Adjust the address code, adjust the brightness, frequency, 8/16 bit UP.

16

Key 3

Adjust the address code, adjust the brightness, frequency, 8/16 bit DOWN.

Self-test procedures

Set DMX address to 000, RGBW full output during 3s, then R, G, B, W fading.

Note:

1.DMX signal cable is three core shielded signal cable, the signal cable with positive, negative, when connect the DMX signal terminals pls pay more attention to the polarity.
2. When connect the decoder, please make sure to the corresponding positive, negative and GND.
3. The cable between DMX controllers, splitters and decoders should not over 300meters.
4. A maximum of 10 DMX Decoders may be connected together via the RJ45 or XLR DMX Connection Ports. DMX signal may be extended further by installing a DMX repeater or splitter
after the 10th DMX Decoder.
5. An additional splitter/amplifier must be added after 32pcs decoders. Cascade connection must not more than 4 PCS.

Safety Information

1.Install in accordance with national and local electrical code regulations.
2. This product is intended to be installed and serviced by a qualified, licensed electrician.
3. The working voltage for the decoder is DC12-48V, DO NOT connect to high voltage power. Install with a compatible constant  voltage power supply or battery with appropriate voltage.
4. Only install compatible 12VDC-48VDC constant voltage luminaires.  Make sure to match power supply voltage to the requirements of the LED light. Ignoring this could lead to a potential fire hazard.
5. This product is rated for indoor use only and is not protected against moisture.
6. Choose an appropriate wire gauge for the maximum potential current load, given your choice of power supply and lights. Keep    in mind that the sum total current for all channels is carried over the shared LED+ terminal, so the total current over the LED+conductor is typically the determining factor in cable choice.
7. Ensure that power is disconnected whenever inserting or removing wires in screw terminals, or connectors in sockets.
8 Ensure that all screw terminals are tightened and all connectors are fully inserted while in operation.

Hot Tags: high frequency 6 channels dmx decoder with on-board display, China, manufacturers, suppliers, factory, customized

 
 
 Technical parameters
Products name High Frequency 6 Channel DMX Decoder with on-board display
Products model GDE0610HF
Housing material & Color Steel & Black
Operating voltage 12-24V or 25-48V
Output Current(Max.) 6CH×10A@12-24V,   6CH×6A@25-48V
Output power(Max.) 720W@12V, 1440W@24V, 1728W@48V
Output type Constant voltage
Grey Levels 16bit (65536 levels)/8bit (256 levels)
PWM Frequency 5K/10K/20K/30KHz Selectable
Size L122×W107×H33mm
Gross weight 450g
Operation temperature Ta: -30 ℃ ~ +55℃
IP rating IP40
DMX IN/ OUT RJ45/XLR
Power in/LED Out 10 Pin Green Block Terminals

Send Inquiry

You Might Also Like