Neon LED Strip Installation Process Need To Pay Attention To What?

The power supply voltage should be consistent with the voltage marked by the Neon LED Strip, and install the appropriate insurance device; use the process, do not use any object wrap, cover Neon LED Strip; interface must be strong, no short-circuit hidden; outdoor installation, the interface The installation of Neon LED Strip in cold weather can be installed for several minutes, so that the body becomes soft, easy to bend, and then power off the installation; Please note that SMD lights can not be Do not damage the wiring on the circuit board; avoid the Neon LED Strip on the ground to avoid scratching or damage the protective layer; do not install or install the lamp during the power supply, only the connection In order to ensure the reliability of the lamp, in order to ensure the reliability of the lamp, it is recommended not to bend in the diameter of 60mm or less, in order to ensure the life of the lamp, in order to ensure the life of the lamp, Do not fold to avoid damage to the lamp beads or cause the sheet to break.
Neon LED Strip because of its high brightness, low energy consumption, more should be to the building decoration, advertising light boxes, jewelry display Taiwan and other bright equipment, but custom Neon LED Strip when you need to consider what aspects?
1, see solder joints. The Neon LED Strip, manufactured by the formal Neon LED Strip manufacturer, is manufactured using solder paste and solder paste and reflow soldering processes. Therefore, Neon LED Strip on the solder joints are relatively smooth and the amount of solder will not be more, the solder joint was arc-shaped from the FPC pad to the LED electrode extension. While the cottage version of Neon LED Strip solder joint solder is not uniform, mostly a dot wrapped around the foot, while there will be different degrees of tin tip appears, which is a typical phenomenon of manual welding.
2, see FPC quality. FPC is divided into copper and rolled copper two, copper clad copper foil is protruding, look at the line from the pad and FPC to see the connection. And rolling copper is close and FPC as a whole, you can bend any bend without the phenomenon of falling off. If you bend over the copper plate will appear off the pad, the maintenance of high temperature will cause the pad off.
3, see Neon LED Strip surface cleanliness. If you use the SMT process Neon LED Strip, the surface cleanliness is very good, do not see any impurities and stains. However, if the use of hand-welding process production of the cottage version of Neon LED Strip, the surface no matter how cleaning, will remain stains and cleaning traces, and in the FPC surface will have flux and tin residue residue.
4, look at the packaging. Regular Neon LED Strip will be anti-static coil tray packaging, usually 5 meters a volume or 10 meters a roll, and then outside the use of anti-static moisture-proof packaging sealed. While the cottage version of the Neon LED Strip because of cost savings, and the use of recycled coil, and then there is no anti-static moisture-proof packaging bags, carefully read the coil can see the appearance of the label to remove the traces and
5, the rules of the Neon LED Strip will be enclosed in the box with instructions and light bar specifications, but also with Neon LED Strip connector or deck; and cottage version of the Neon LED Strip box is not the annex , Because some manufacturers, after all, can save the province.
Learn these six ways to determine the quality of the Neon LED Strip, all qualitative Neon LED Strip can not escape your discernment.
Currently on the market more use of low-voltage Neon LED Strip, because of its low cost, light angle, the production process is simple, safe and environmentally friendly, easy to use and other factors, which gradually replace the old-fashioned LED straight lamp. Neon LED Strip Features and Benefits:
1) pure color: Neon LED Strip high-brightness patch LED for the light-emitting components, so with the advantages of LED light-emitting components, light color pure, soft, no glare. Both as decorative purposes, but also for lighting purposes.
2) Soft: Neon LED Strip with a very soft FPC for the substrate, can be bent without breaking, easy to shape, suitable for a variety of advertising modeling needs.
3) small heat: Neon LED Strip light-emitting element is the LED, because a single LED power is very low, generally 0.04 ~ 0.08W, so the heat is not high. Can be used as the aquarium underwater decorative lighting, and will not produce a lot of heat caused by water temperature rise, affecting the growth of ornamental fish.